Sanghvi Industrial Electronics

GD100PIY120C6SN IGBT MODULE
GD100PIY120C6SN IGBT MODULE
GD100PIY120C6SN IGBT MODULE

Description The Broadcom® ACPL-C79B/C79A/C790 isolation amplifiers are designed for current and voltage sensing in electronic power converters in applications including motor drives and renewable energy systems. In a typical motor drive implementation, current flows through an external resistor and the resulting analog voltage drop is sensed by the isolation amplifier. A differential output voltage that is proportional to the current is created on the other side of the optical isolation barrier. For general applications, the ACPL-C79A (±1% gain tolerance) and the ACPL-C790 (±3% gain tolerance) are recommended. For high precision applications, the ACPL-C79B (±0.5% gain tolerance) can be used. The product operates from a single 5V supply and provides excellent linearity and dynamic performance of 62 dB SNR. With 200 kHz bandwidth, 1.6 μs fast response time, the product captures transients in short circuit and overload conditions. The high common-mode transient immunity (15 kV/μs) of the ACPL-C79B/C79A/C790 provides the precision and stability needed to accurately monitor motor current in high noise motor control environments, providing for smoother control (less “torque ripple”) in various types of motor control applications. Combined with superior optical coupling technology, the ACPL-C79B/C79A/C790 implements sigma-delta (Σ-Δ) analog-to-digital converter, chopper stabilized amplifiers, and a fully differential circuit topology to provide unequaled isolation-mode noise rejection, low offset, high gain accuracy and stability. This performance is delivered in a compact, auto-insertable Stretched SO-8 (SSO-8) package that meets worldwide regulatory safety standards. Features  ±0.5% High Gain Accuracy (ACPL-C79B)  –50 ppm/°C Low Gain Drift  0.4 mV Input Offset Voltage  0.05% Excellent Linearity  62 dB SNR  200 kHz Wide Bandwidth  3V to 5.5V Wide Supply Range for Output Side  –40°C to +105°C Operating Temperature Range  Advanced Sigma-Delta (Σ-Δ) A/D Converter Technology  Fully Differential Isolation Amplifier  15 kV/μs Common-Mode Transient Immunity  Compact, Auto-Insertable Stretched SO-8 Package  Safety and Regulatory Approvals: – IEC/EN/DIN EN 60747-5-5: 1414Vpeak working insulation voltage – UL 1577: 5000 Vrms/1 minute double protection rating – CSA: Component Acceptance Notice #5 Applications  Current/Voltage Sensing in AC and Servo Motor Drives  Solar Inverters, Wind Turbine Inverters  Industrial Process Control  Data acquisition systems  Switching Power Supply Signal Isolation  General Purpose Analog Signal Isolation  Traditional Current Transducer Replacements CAUTION! It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this data sheet are not to be used in military or aerospace applications or environments.

Description The ACPL-P314/W314 consists of a GaAsP LED optically coupled to an integrated circuit with a power output stage. These optocouplers are ideally suited for driving power IGBTs and MOSFETs used in motor control inverter applications. The high operating voltage range of the output stage provides the drive voltages required by gate-controlled devices. The voltage and current supplied by this optocoupler makes it ideally suited for directly driving small or medium power IGBTs.  Applications  Isolated IGBT/Power MOSFET gate drive  AC and brushless DC motor drives  Industrial inverters  Inverter for home appliances  Induction cooker  Switching power supplies (SPSs)   Features  High-speed response  Ultra high CMR  Bootstrappable supply current  Available in Stretched SO-6 package  Package clearance/creepage at 8 mm (ACPL-W314)  Safety approval: — UL1577 recognized with 3750 Vrms for 1 minute for ACPL-P314 and 5000 Vrms for 1 minute for ACPL-W314 — CSA Approved — IEC/EN/DIN EN 60747-5-5 Approved — VIORM = 891 Vpeak for ACPL-P314 — VIORM = 1140 Vpeak for ACPL-W314  Specifications  0.6-A maximum peak output current  0.4-A minimum peak output current  0.7-μs maximum propagation delay over temperature range  I CC(max) = 3-mA maximum supply current  25 kV/μs minimum common mode rejection (CMR) at VCM = 1500V  Wide VCC operating range: 10V to 30V over temperature range  Wide operating temperature range: –40°C to 100°C 

The TJA1050 is the interface between the Controller Area Network (CAN) protocol controller and the physical bus. The device provides differential transmit capability to the bus and differential receive capability to the CAN controller. The TJA1050 is the third Philips high-speed CAN transceiver after the PCA82C250 and the PCA82C251. The most important differences are: • Much lower electromagnetic emission due to optimal matching of the output signals CANH and CANL • Improved behaviour in case of an unpowered node • No standby mode. This makes the TJA1050 eminently suitable for use in nodes that are in a power-down situation in partially powered networks. 

Features  15 kV/µs minimum Common Mode Rejection (CMR) at VCM= 1 kV for HCNW2611, HCPL-2611, HCPL-4661, HCPL-0611, HCPL-0661  High speed: 10 MBd typical  LSTTL/TTL compatible  Low input current capability: 5 mA  Guaranteed AC and DC performance over industrial temperature: –40°C to +85°C  Available in 8-Pin DIP, SOIC-8, widebody packages  Strobable output (single channel products only)  Safety approval – UL recognized – 3750 Vrms for 1 minute and 5000 Vrms for 1 minute per UL1577 CSA approved (5000 Vrms/1 Minute rating is for HCNW137/26X1 and Option 020 [6N137, HCPL-2601/11/30/31, HCPL-4661] products only) – IEC/EN/DIN EN 60747-5-5 approved with:  VIORM = 567 Vpeak for 06xx Option 060  VIORM = 630 Vpeak for 6N137/26xx Option 060  VIORM =1414 Vpeak for HCNW137/26x1  MIL-PRF-38534 hermetic version available (HCPL-56xx/66xx) 

■ Description PC457L0NIP0F Series contains a LED optically coupled to an OPIC chip. It is packaged in a 5 pin Mini-flat. Input-output isolation voltage(rms) is 3.75 kV. High speed response (TYP. 1Mb/s) and CMR is MIN. 15 kV/µs.  ■ Features ■ Agency approvals/Compliance High Speed 1Mb/s, High CMR Mini-flat Package ∗OPIC Photocoupler 1. Mini-flat 5 pin package 2. Double transfer mold package (Ideal for Flow Soldering) 3. High speed response (tPHL : TYP. 0.2 µs, tPLH : TYP. 0.4 µs) 4. High noise immunity due to high instantaneous common mode rejection voltage (CMH : MIN. 15kV/µs, CML : MIN. −15kV/µs) 5. High isolation voltage between input and output (Viso(rms) : 3.75 kV) 6. RoHS directive compliant

PC929L SHARP OPTOCOUPLER IC
PC929L SHARP OPTOCOUPLER IC
PC929L SHARP OPTOCOUPLER IC
PC929L SHARP OPTOCOUPLER IC